Detailed Photos
Distillation-The Hybrid still
The addition of a rectification column can allow the distiller to produce distillate with an abv beyond 80%, The more trays that are included in a column, the higher the abv that can be achieved. Each tray is in itself, a single disdtillation.
Pot still size: Hybrid pot stills are available in a variety of sizes from 50L to 5000L.
Configurations:
Hybrid pot stills can be built either of copper or stainless steel. When built from stainless steel, the bottom and side shell of the pot are made of stainless, while the top of the pot is built from copper and welded together.
The Hybrid pot still can be build with various head designs, depending on the spirits being produced. The tray quntity in the rectification column is dependent on the desired ABV of the final distillate.
The condenser, which cools the vapour to liquid, is of a shell and tube design and can be built from either copper or stainless stee.
.
Customized Distiller for
Grappa, fruit distillates, gin, vodka, whiskey, rum, brandy, tequila from 200L to 5,000L .Fast Delivery.
20 years of manufacturing experience. Contact Us For The Offer!
Powered by steam or electricity
Main pot, 4 plate coloumn, dephlegmator in C12200 copper
4 Plate column with dephlegmator and full cip
Botanical basket lined with copper
Stainless steel condensor
Stainless steel parrot and glass
Agitator with ATEX motor
Cip Pump with ATEX motor - hard piped to CIP spray balls
Frame and table to support column, botanical basket and condensor
configuration
| Typical Distillation Times: | • 1 hour heat up
• 2-4 hr stripping run
• 3~5 hour distillation time |
| Structure: | -1 x SS304/red copper still pot
-1 x Red copper goose neck(helmet)
-1 x SS304/red copper Gin basket
-1 x Red copper 4~12plate distillation colum
-1 x SS304/red copper dephlegmator
-1 x SS304/red copper condenser
-1 x SS304 parrot outlet
-1 x SS304 support for condenser |
| Options: | High Torque Mash Agitator, CE/UL/CSA/ATEX Explosion Proof Voltage:customize
Copper Kettle
Copper dephlegmator/condenser
CIP pump and CIP pipe
Bottom spirit storage tank |
| System at a Glance: | Best use: Dedicated Stripping Still, Whiskey, Brandy, Tequila, Gin or Rum Production Acohol content after distillation about 70+-10%
Versatile and Cost Effective
Easy Maintenance with Clean in Place
304 Polished and Brushed Stainless and Polished Copper construction |
hot wort grant to provide a buffer to the pump during reciculation and run off from the lauter tun
heat exchanger to cool the wash during transfer to the fermenter
hot water recovery option available
pumps
digital scales
complete grain management including:
roller mills
hammer mills
augers and conveyors
grist hoppers
slide gates
hydrators
CIP tanks and skid options
yeast brinks and propagators
barrel dumps
boilers
glycol chillers
Standard distillery equipment Features Hot water:
hot wort grant to provide a buffer to the pump during reciculation and run off from the lauter tun
heat exchanger to cool the wash during transfer to the fermenter
hot water recovery option available
pumps
digital scales
complete grain management including:
roller mills
hammer mills
conveyors
grist hoppers
slide gates
hydrators
CIP tanks and skid options
yeast brinks and propagators
barrel dumps
boilers
glycol chillers
Electrical
note: These electrical guidelines are for planning purposes only. Complete detailed electrical requiremsents will be issued with the purchase of a brewing system from Gedrick.
Standard electrical for our equipment is 208vAC, 3 phase, 60 hertz,4 wire,
A200Amp service is generally acceptable for the brewery, but may be affected based on cstomer power supply.
we can adapt the requirements prior to finalizing a design.
ceiling heights
for planning purposes, smaller systems of 5-10 barrels should consider ceiling heights of 12' to 15' in brewhouse and cellar areas.
Microbreweries and production breweries will require additional ceiling heights due to the large sizes of the vessels.
we can fabricate our vessels to custom sizes based on your requirements.
Drainage
drains are required in the brewhouse, fermentation, walk-in cooler (if applicable), boiler room, and any other area where water and spillage may occur (e.g. kegging/bottling).
floors should have a recommended pitch of 1/4" per foot towards drains.
we recommend channel drains with stainless steel of fiberglass grating.All drains should be sized adequately to handle 4-6 barrels of effuent of every 1 barrel of beer produced.
Water
Main water supply to your brewery is recommended to be 60 psi@25-30 GPM. uniform water flow to the brewhouse is critical and should not be affected by water demand elsewhere in the building.
Hot and cold hose bibs are required in all brewery spaces and lab areas.
If kegging or bottlingwill be done, a water supply will be needed in these areas.
Filtration may be necessare for city water. A water analysis will determine if a filter is required.
Packaging & Shipping
Delivery date: 45-75 days from the prepayment date,
Shipping: by ocean
After Sales Service
- Customized according to your personal request based on our standard configuration
- After Sale Service for whole life if you have request
- 24hours on line, supply solutions any time
- 3 Years Warranty for the Main Equipment
- Spares parts replacement and repair service
- Engineer goes to your city for installation, debugging and brewing training if you need
- Provide the import documents that you need for customs clearance and reduce Tax.
- Supply the latest news for the brewing industry and brewing technology
- Port to Port, Door to Door service
One Stop Turnkey Project service
FAQ
1.Q: Are you professional Supplier and tanks Manufacture ?
A: We are the manufacturer of distilling equipment for 15 Year and deal in export business since 10 years ago .
2.Q:Can I have the customized products with personal design?
A:Yes,we support any of your wish design,can design and manufacture as client's requirements.
3.Q: Can you guarantee your distilling equipment quality?
A: All of the equipment will be inspected before the package, appliance of the international Standard.
4.Q:How about the after sales service?
A:For our after-sale service, we promise all life of technical support to all client.
All of our products is available with 10 years warranty even for spare parts within quality warranty period, our service is free of charge.
5.Q: Which export port you use?
A:Commonly we will use ningbo port, sometime, can be other port as your wish.
6.Q: I am green hand in spirits distilling industry? Could you supply training for us?
A: Yes, our engineer and cooperated master distiller can supply the installation equipment and distilling training service overseas.
7.Q: what is your payment item ?
A: We accept 50%TT + 50%TT as for the balance payment before the delivery
Certifications
